ICOM 200 Manuale Utente Pagina 1

ICOM® 200/201/241

ICOM-manual First steps Power supply The ICOM-200/201 uses a power supply with 8-12 VDC, 1A. Minus is placed on the pin of the power supply connector.

ICOM-200 / 201 RUN mode If the DIP-switch “PC/Run” is in position “Run”, the program in the ICOM-200/201 is executed immediately after a reset. Debu

ICOM-manual SLEEP mode The ICOM-200/201 can be put into sleep mode if the Tiny-Tiger® inside has a real time clock. In sleep mode the power consumptio

ICOM-200 / 201 2 To put the ICOM-200/201 into sleep mode, the alarm time for the Tiny-Tiger® clock has to be set. Following that the ICOM-200/201

ICOM-manual Keyboard The ICOM-200 has a 20 key matrix keyboard. The keyboard is devided into two blocks. The first block has four vertically arranged

ICOM-200 / 201 '-------------------------------------------------------------------- '----- ICOM_KEYB.TIG '--------------------------

ICOM-manual LC display The ICOM-200 has a graphic LC display with a resolution of 128 x 64 pixel. There’s a special device driver to control this dis

ICOM-200 / 201 Serial Interface As a standard the ICOM-200 and ICOM-201 have two serial interfaces. From these the port Ser0 can by choice be config

ICOM-manual The pins of serial port 0 are located on the DB-37 connector: RS232 DB-37 TXD0 (Output) 16 RXD0 (Input) 17 RTS0 36 CTS0 35 2 RS485 The

ICOM-200 / 201 Opto inputs The ICOM-200/201 has eight optocoupler inputs suited for an input voltage range of 5...12 VDC. To use higher input voltag

ICOM-manual '-------------------------------------------------------------------- '----- ICOM200_OPTOIN.TIG '--------------------------

ICOM-200 / 201 Power outputs The power outputs of the ICOM-200/201 are extended outputs of the Tiny-Tiger®, which are equiped with a driver IC type

ICOM-manual '-------------------------------------------------------------------- '----- ICOM200_OUTPUTS.TIG '-------------------------

ICOM-200 / 201 Analog inputs The analog inputs have a hardware resolution of 10 bit, nevertheless by software interpolation a resolution of 12 bit c

ICOM-manual The configuration is done with jumpers on the backside of the board (see picture). To alter the configuration it is neccessary to open the

ICOM-200 / 201 Configuration 0…10V To use the analog inputs with voltages of up to 10V DC, it is neccessary to change the jumper configuration. Plea

ICOM-manual Setting the amplification The analog inputs of the ICOM-200 / 201 have an adjustable input amplifier. The amplification can be set to a fa

ICOM-200 / 201 '-------------------------------------------------------------------- '----- ICOM200_AD.TIG '-------------------------

ICOM-manual MF-2 Keyboard The ICOM-200 and ICOM-201 both have a connector for a MF2 keyboard. With this it is possible to connect a common PC keyboard

ICOM-200 / 201 '-------------------------------------------------------------------- '----- ICOM200_MF2.TIG '------------------------

About this manual 1 ICOM-200 / 201 2 ICOM-241 3 Advice and support 4 Register 5

ICOM-manual CALL SetLcdOutputPos( LCD, 9, 0 ) PRINT_USING #LCD, wKey BITAND 0ffh CALL SetLcdOutputPos( LCD, 9, 1 ) PRINT_U

ICOM-200 / 201 2 ENDIF ENDWHILE END SUB SetLcdOutputPos( WORD wDevId; BYTE Column, Row ) PRINT #wDevId, "<1BH>A";CHR$( C

ICOM-manual TINY-Tiger® Pins The ICOM-200/201 has, in addition to the extended I/O pins with optocouplers and transistors, some standard pins of the T

ICOM-200 / 201 Technical data LCD: Graphical display with 128 x 64 pixel and LED backlight. 2 Keyboard: Keyboard matrix with 20 keys and addition

ICOM-241 3 ICOM-241 The ICOM-241 is the most cost effective solution of the ICOM family. The processor used is a Tiny-Tiger® Economy. The ICOM-241 ha

ICOM-manual First steps Power supply The ICOM-200/201 uses a power supply with 8-12 VDC, 1A. Minus is placed on the pin of the power supply connector.

ICOM-241 RUN mode If the DIP-switch “PC/Run” is in position “Run”, the program in the ICOM-241 is executed immediately after a reset. Debugging is no

ICOM-manual Opto inputs The ICOM-241 has eight optocoupler inputs suited for an input voltage range of 5...12 VDC. To use higher input voltages, as 24

ICOM-241 '-------------------------------------------------------------------- '----- ICOM241_OPTOIN.TIG '----------------------------

Copyright © by Wilke Technology GmbH Krefelder Str. 147 52070 Aachen / Germany manual version 1.4 This manual, together with the hardware and sof

ICOM-manual Power outputs The power outputs of the ICOM-241 are extended outputs of the Tiny-Tiger® Economy, which are equiped with a driver IC type T

ICOM-241 Serial interface As a standard the ICOM-241 has two serial interfaces. From these the port Ser0 can by choice be configured as RSR232 or RS4

ICOM-manual The pins of serial port Ser0 are located on the DB25 connector. The pin layout is shown in the table below: 3 RS232 Pin DB25 socket TxD0

ICOM-241 Placing or removing of the ICs is only allowed without power supply. ! RS485 Pin DB25 socket TXD0 (A) 18 RXD0 (B) 17 Layout of DB25 socke

ICOM-manual '-------------------------------------------------------------------- '----- ICOM200_RS232.TIG '---------------------------

ICOM-241 Analog inputs The analog inputs of the ICOM-241 have an input range from 0...5V DC. The hardware resolution is 10 bit and can be raised to 1

ICOM-manual 3 ICOM-manual 3-12 Wilke Technology GmbH • 0241/918900 • http://www.wilke.de/ • [email protected] 3 Circuit of analog inputs 3-12 Wilke Tec

ICOM-241 '-------------------------------------------------------------------- '----- ICOM200_AD.TIG '--------------------------------

ICOM-manual Pin layout 25-pin D-Sub connector The 25-pin D-Sub connector carries all available I/O pins (except for serial port 0) of the ICOM-241. 3

ICOM-241 Technical data Interface: 1 x RS232 1 x RS232/RS485 selectable. Analog In: 4 x 0...5V with input amplifier 1 < V < 10 Resolutio

Contents Contents 1 About this manual 1-1 Typographic conventions and symbols 1-2 2 ICOM-200 / 201 2-1 Versions 2-1 Differences between ICOM-200

ICOM-manual ICOM 241 – 24V The ICOM-241 – 24V is a variant of the ICOM 241. It needs a supply voltage between 14V and 24V DC. The serial port SER1 is

ICOM-241 Connection to PC For programme download, debugging and other communication with a PC use a crosslinked cable (null modem) Technical data

Hints and Help 4 Hints and help When you have problems with a Tiger-BASIC® program: Try to reduce the problem to a short and simple sample progr

ICOM-manual 4 4-2 Wilke Technology GmbH • 0241/918900 • http://www.wilke.de/ • [email protected]

Index 5 Register Amplification 2-18 analog inputs 2-15, 3-12 Display 2-8 Goldcap 2-4 I/O pins 2-24 ICOM-241 3-1 LC display 2-8 Loading time 2

Contents Opto inputs 3-4 Power outputs 3-6 Serial interface 3-7 RS232 3-7 RS 485 3-8 Analog inputs 3-11 Pin layout 25-pin D-Sub connector 3-14 T

General 1 About this manual 1 This manual does introduce you into the control of the ICOM industry computer family for a fast and easy use. The ICO

ICOM-manual 1 Typographic conventions and symbols Following fonts and symbols are used for fast identification of important informations: Element Mea

ICOM-200 / 201 2 ICOM-200 / 201 Versions 2 This manual describes the ICOM200 and ICOM201 til version V1.3. Newer versions are described in separate